Adapters and distributors
The right connection
87 results:
- Accessory family: Other adapters and distributors
- Description: Node for voltage supply
- Accessory family: Other adapters and distributors
- Connection type head A: Male connector, M12, 5-pin, A-coded
- Description: End connector for serial connection in combination with STR1-XXA
- Accessory family: Other adapters and distributors
- Description: Muting connector
- Accessory family: Other adapters and distributors
- Description: IO-Link connector
- Accessory family: T-junctions
- Connection type head A: M12, 5-pin, A-coded
- Connection type head B: Female connector, M12, 5-pin, A-coded
- Connection type head C: Male connector M12 5-pin A-coded
- Note: Male connector M12, 5-pin, straight, A-coded to 2 x female connector M12, 5-pin, straight, A-coded
- Accessory family: Y-junctions
- Note: Y-junction for serial connection of IN4000 Standard
- Accessory family: Y-junctions
- Connection type head A: M8, 4-pin
- Connection type head B: Male connector, M8, 3-pin
- Connection type head C: Male connector M8 3-pin
- Note: Signal interrogation and logic interrupt, female connector M8, 4-pin, straight to 2 x male connector M8, 3-pin, straight
- Accessory family: Other adapters and distributors
- Note: Diode module, Connects multiple shorting pressure sensitive mats (up to 4)
- Accessory family: T-junctions
- Connection type head A: Female connector, M12, 5-pin, A-coded
- Connection type head B: Male connector, M12, 5-pin, A-coded
- Description: T-piece for simultaneous connection to sender and receiver, splits the cable from the control cabinet to the sender and receiver
- Note: 5-pin
- Connection type head A: Male connector, M12, 4-pin, straight, B-coded
- Description: PROFIBUS DP, terminal resistor
- Accessory family: Bus adapter
- Connection type head A: Female connector, M12, 8-pin, straight
- Note: PROFIBUS-DP adapter cable (PROFIBUS IN, PROFIBUS OUT, and voltage supply), suitable for drag chain
- Accessory family: Other adapters and distributors
- Connection type head A: End plug
- Connection type head B: -
- Note: End connector for serial connection in combination with T40-A2191N Y-junction
- Accessory family: Other adapters and distributors
- Description: For connecting the microScan3 - PROFINET M12 variants on push-pull
- Accessory family: T-junctions
- Connection type head A: M12, 5-pin, A-coded
- Connection type head B: Female connector, M12, 8-pin, A-coded
- Connection type head C: Male connector M12 5-pin A-coded
- Note: Male connector M12, 5-pin, to 1 x female connector M12, 8-pin, to 1 x female connector M12, 5-pin, for connecting on IO-Link-Master
- Accessory family: T-junctions
- Connection type head A: M12, 5-pin, A-coded
- Connection type head B: Female connector, M12, 8-pin, A-coded
- Connection type head C: Male connector M12 8-pin A-coded
- Note: Male connector M12, 8-pin, to 1 x female connector M12, 8-pin, to 1 x female connector M12, 5-pin, for connecting of a PLC
- Accessory family: Y-junctions
- Connection type head A: Female connector, M12, 8-pin
- Connection type head B: 2x cables
- Description: Y-distribution, shielded, female connector, M12, 8-pin, to 2x open cable ends, 4-pin, 0.25 mm², twisted pair, length 2x2 m
- Accessory family: Y-junctions
- Connection type head A: M12, 3-pin, A-coded
- Connection type head B: Male connector, M12, 4-pin, A-coded
- Connection type head C: Male connector M12 4-pin A-coded
- Note: Female connector M12, 4-pin, straight to 2 x male connector M12, 4-pin, straight
- Accessory family: Junction boxes
- Note: Dimensions (W x D x H) 57 mm x 130 mm x 94 mm, for electrical connection of level probe LFH
- Accessory family: Other adapters and distributors
- Note: Terminal with 182 Ohm resistance, for pin 9 and 10 on the system connection, to improve the EMC behaviour if the EFI interface is not used